These are the steps to configure the Ubiquiti Bullet. Mode of operation that will be connected to a wireless router in the WAN port so wireless router. Like all Ubiquiti equipment the Bullet is capable of being set in any wireless mode – access point, station, bridge, router, AirMax (for P2P/P2MP) AP/station. Bullet2HP, Bullet2-HP by Ubiquiti Networks, High Power GHz bg AP or Client Bridge, CPE, Outdoor, Bullet2HP b/g mW Indoor/Outdoor Access Point / Client Device by Ubiquiti Networks Pre-Configure, Burn In & Test.
|Published (Last):||27 November 2015|
|PDF File Size:||16.82 Mb|
|ePub File Size:||16.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
About Us We are the website for boating enthusiast from the novice to the old salt desiring to learn more about their boat or boating in general. I connect all of my devices to the tplink’s wireless network and it routes them through the m2.
So far so good, but when I diagnosed the ‘cannot display web page’ issue, the result was something that indicated a DNS problem – like ‘cannot resolve msn. From a factory reset, the Bullet can be accessed through its standard IP What I found was either information scattered all over the internet that didn’t give me the whole picture or I found the complete packages with all the goodies setup and ready to go. Since I have installed this I am hearing from folks that have antenna’s above 15db that are not experiencing problems, so I would say up to 15db should be fine.
I’ll have to look at my notes. A walkthrough step-by-step guide on how to set up a Ubiquiti device to connect to a remote access point or hotspot in order to share internet with multiple local devices.
Configguration Hyjack for your reply. I am like you as far as involved in computers for a long time but when I first set my ubiquity up it was a bear, which is why I wrote this article. I’ll certainly be adding this to my boat for the summer. Originally Posted by TimG.
That is the only thing I can think of. New member in FL I’m fairly new to boating, according to my skill level, very new. I spent quite a bit of time corresponding with the folks at ubiquity getting help. A higher gain antenna like your 8dBi Trendnet will only cast your signal farther and interfere with surrounding networks.
Heres their web site on it if the ubiquity scenario fails.
We have a Netgear N wireless router that is new in its box and never used. George I can’t definitively answer that question for you. To configure the Bullet as an access point, change the following configurations in the Wireless tab:. For the Raspberry, the interface used is the Ethernet e.
TimG – December 31st, To connect to an unsecured network, bulle2thp pull up ‘config-2’ and apply it, and poof2 happens! The pre-configured packages are very nice if you are willing to spend the money.
Avcess do know many people I have talked to have opted to use non-shielded cable, but in your situation with the cable running so close to the VHF and SSB, I think you are making a wise choice by choosing shielded cable for that portion of the run.
Which brings me to the only question I have – thus far at least – while I am going to get the outdoor cable to prevent UV degradation of the cable jacket, do I want the cable to also be shielded?
Hi, we are in the same situation, travelling on a boat all the time, conecting to different marinas accfss the bullet.
Thank you, Jack, for your helpful reply. With that in mind, my observations is that programming my computer and the bullet prove very acvess.
In that regard, I would like to thank TimG for the detailed directions on how to install and configure a bullet. Another reason is once setup you will no longer be required to change the laptops IP to log onto the Bullet. Help a noob setup a Bullet 2hp self.
An IP must also be manually set for the WiFi devices. The tplink dhcp’s an address from the m2. Like you I was intimidated by the thoughts of trying to set up a bullet but the more I researched the less apprehensive I became.
The Netgear can still be used in switch made too for up to 4 other the bullet using 1 hardwired devices. We also cover common procedures such as “how to anchor properly” or “how to lock through a dam”. What you are getting is a system that has been programmed so it is roughly plug it in, install some software and you are up and running. After the frustrations of trying to connect to the internet with the usual methods I finally decided to bite the bullet, or at least install one, a Ubiquity Bullet2HP to be exact.
Attachment This setup is nothing more than a repeater that boost the signal to a usable level, you still have to have someone providing internet access either via a free wifi access point or provide you with the proper login information for secure wireless networks.
The best solution might be to add the google DNS. TimG – February 1st, TimG – January 26th, I’m using acfess as home access points.
Ubiquiti submitted 2 years ago by HJGamer. Share Share this post on Digg Del. Let us know which method you pursue, and we are always willing to offer help when we can. Bullethp appreciate it a great deal. Accfss Change and then Apply. Should Bullet or router or both be password protected? I can read this sentence a couple of ways but I think you are saying that the Netgear Wireless Router is in AP mode and is given a static IP address as one of the settings that was defined in the Bullet setup.
Setting IP by ifconfig will assign the IP temporarily to the port. You will likely have to explain what you are doing to the technician so he can understand your needs. Ubiquity has some pretty good support resources at Ubiquiti Networks, Inc.