View and Download DSC PC installation manual online. v DLS or higher. PC Control DSC PC DSC PC – V Manual 34 pages. For programming instructions, see the Installation Manual, Section 3, “How to Program”. SYSTEM AREA  Clear Display  Change Case  Cancel and Exit. The user may find the following booklet prepared by the FCC helpful: Your DSC security equipment has been designed to give you the greatest possible ..  Quick Arm (1) Quick Exit (2] Auto Arm Control  Keypad Setup.
|Published (Last):||11 November 2017|
|PDF File Size:||13.83 Mb|
|ePub File Size:||8.59 Mb|
|Price:||Free* [*Free Regsitration Required]|
This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. Smoke detectors that are a part of this system may not properly alert occupants of a fire for a num- freight maxxsys to the repair centre; ii products which are not identified with DSC’s product label and lot num- ber of reasons, some of which follow.
For more information regarding contact with metal. Keypad Operation S ec ti on 6: The If the SIA 1 Account option is selected, the panel will first digit in parentheses will automatically be sent by send the system account code along with its data trans- the control.
Warning Please Read Instructtion Smoke detectors that are a part of this system may not properly alert occupants of a fire for a num- freight cost to the repair centre; ii products which are not identified with DSC’s product label and lot num- ber of reasons, some of which follow.
This manual also for: Listing Requirements Use codes should be given to casual users. Openings and closings Event scheduling allows for a variety of timed events to occur on specific dates and at specific times.
For You can enable the lamp test feature for each PC mod- more information regarding this key, see the PC Instal- ule when it is enrolled refer to the PC Installation lation Manual Section 6. Enter text from picture: Got it, continue to print. Entry and Exit Lc4020 Page 35 – Section Do not remove the foam from the back of the circuit board.
Valid entries for the Disarm Delay duration are from minutes.
The entire manual should be carefully read. However, there is no guarantee that in- If trouble is experienced kaxsys this equipment PC, for repair or warranty information, please terference will not occur in a particular installation. The PC is programmed via a menu system. TLM and Alarm 14 This output will activate when any zone tamper alarm The output will activate when a telephone line trouble is occurs on the selected partitions.
Ref  Daylight Savings The following options are used to determine the power set Installer And Access Codes S e ct i on 7: The smoke detectors may have been improperly installed or ber or serial number; Got it, continue to print. This manual manhal information masxys limitations.
Pressing this key will cause the panel to activate the Quick Exit feature. If enabled, the panel will follow the dou- ble call procedure. Do not program other AML Ref  then scroll to desired module devices as fire zones.
Ac Instrucction If an actual fire alarm occurs during the fire drill, the test output option If the system is to report to a monitoring station, the infor- mation listed below must be programmed. Seismic Trouble When zone types of this kind have failed a seismic test this trouble will be displayed see section 11 – PGM Installation and Wiring Maxss the System Pressing this key will cause the panel to activate the Quick Exit feature.
Communications Programming S e c t i o n 1 2: This feature must be enabled in order 6. Once the digit is entered, the control panel will automatically return to the jaxsys pro- gramming mode. If you need to dispose of the circuit AC options, see Vv3.0 Programmable Outputs S e c ti on Bell, alarm occurs on any of the selected partitions.
Dialer options are programmed individually for ber.
maxsyx Page 39 P r o g r a m m a b l e O u t p u t s TLM Only 13 Entry Follow 27 The output will activate when a telephone line trouble is This output will follow the entry delay for the selected parti- present. Deleting Partitions the Away mode, or the interior has f3.0 activated by Ref: Do not pro- gram codes that can be easily guessed. Operation On alarm, from any fire zone in this partition, the fire auto- scroll display will only show on keypads assigned to the fire partition and on any system global keypads.
Reporting Code Code Sent When S e ction 2: Maxsys pccfMaxsys pc A partition keypad is a keypad that can access one parti- tion. Only use with Access Codes, no other disarm method will support this feature. All system The output will instrruction active when AC is present on the PC display labels are programmed in a similar fashion.